david

Forum Replies Created

Viewing 5 posts - 1 through 5 (of 5 total)
  • Author
    Posts
  • July 10, 2008 at 9:36 am in reply to: usb-camera on v90L #13487
    david
    Member
    • Total Post: 6
    • Newbie
    • ★

    Hello,
    the version is 4.02 (Built 0554.512),
    XPE-V. 5.01 SP2

    Regards,
    David

    July 9, 2008 at 2:22 pm in reply to: usb-camera on v90L #13474
    david
    Member
    • Total Post: 6
    • Newbie
    • ★

    Hello,

    I don´t know the firmware-version, the OS is as it was delivered, WinXP Embedded with SP2. On a full winxp the camera shows on mycomputer with a camera-symbol. When I open it, it shows the content from the sd-card.

    I´ve allready tried to use a card-reader – it works properly – but the original docking station would be more comfortable.

    Thanks & Regards,
    David

    April 9, 2008 at 12:08 pm in reply to: USB Imaging 1.4 Released! #12574
    david
    Member
    • Total Post: 6
    • Newbie
    • ★

    Hi,

    I can´t get to the BIOS, the only thing I see after switching it on is the fullscreen wyse-logo.

    Regards, David

    April 9, 2008 at 11:48 am in reply to: USB Imaging 1.4 Released! #12571
    david
    Member
    • Total Post: 6
    • Newbie
    • ★

    @thinkthin wrote:

    I know this sounds weird but what you get the blinking cursor can you then unplug the unit, remove the cover and re-set the CMOS jumper switch next to the battery. Just move it across to the the middle and outside pin and then move the jumper back to its original position,

    Cheers,
    -TT

    Hello,

    I moved the CMOS-jumper to the other position and then back to its original position, but now not even the BIOS runs through – after starting it hangs at the wyse-logo.
    I guess I´ll have to send it back…

    Regards, David

    March 17, 2008 at 10:59 am in reply to: USB Imaging 1.4 Released! #12207
    david
    Member
    • Total Post: 6
    • Newbie
    • ★

    Hello,

    I´ve tried to flash a V10L (Model VT6048) with the new image-file v6.01.08 from wyse, but got an error-msg after running the .bat-file.

    Searching for: (~)
    
'' to ''
    
Unable to Open Source ()
    
Transfer Error!
    
Program Terminated... Rebooting System
    
C:>

    First, there was no V10L.bat and no V10L-Dir in the Wyse_USB_Imager_Files directory, so I copied the V90L.bat file to V10L.bat and modified it like this:

    dl "=1V12,=push,=V10L,"

    Then I created the V10L directory and copied the 1V12_6.0.1_08-128.i2d-file from wyse in it and renamed it to 1V12.i2d.

    Before flashing, I switched the EHCI-mode to disabled, as described in the pdf-manual.
    But after flashing (I think it has read the file, because it took some time to get at 100% at one line), I got the error-msg above and my V10L does not boot from harddisk any more (it shows only a blinking cursor).

    Then I´ve tried flashing it again and used another image-file (1V12-6.0.0_14.08-128.i2d), but the errror-message was shown again.

    Can anyone help me?

    Regards, David

  • Author
    Posts
Viewing 5 posts - 1 through 5 (of 5 total)