WT3125SE and WT3360SE

  • This topic is empty.
Viewing 9 posts - 1 through 9 (of 9 total)
  • Author
    Posts
  • #5386
    yobortsa
    Member
    • Total Post: 5
    • Newbie
    • ★

    Hi all,

    I have come across some WT3125SE and WT3360SE terminals but I don’t have power supplies for them.

    I have hooked up 12V DC to the 3125’s and the ethernet light flashes but I don’t get anything on a monitor. The keyboard lights flash momentarily when I power up the device.

    Is there something I need to do on the network side to get anything out of these or might there be something wrong with this unit?

    Any help would be appreciated – I basically want to know what I can to to see if they are working.

    Thanks, David 🙂

    #16724
    thinkthin
    Member
    • Total Post: 1686
    • Jacked into The Matrix
    • ★★★★★★

    Hi,

    The video out could be toast, if you can get the IP address it grabs from the DHCP server (does it get one?) try using VNC viewer to the unit -if you can VNC (assuming its still installed on the unit as it would from the factory) you will know the video is the issue,

    Cheers,
    -TT

    #16726
    yobortsa
    Member
    • Total Post: 5
    • Newbie
    • ★

    I don’t seem to be getting an IP address from my DHCP server.

    I also set up a packet sniffer on an isolated network segment and the unit doesn’t seem to be sending anything out either.

    What normally happens if you turn them on? Should you see something on the monitor? ..or do they wait until they have an IP address and a server to activate them before you seen anything?

    I got them in a bundle of stuff at an auction – beats me what to do with them.

    I’m not getting a power LED on front of the unit either and the power button doesn’t appear to do anything.

    Thanks,

    David

    #16727
    thinkthin
    Member
    • Total Post: 1686
    • Jacked into The Matrix
    • ★★★★★★

    Yep, you should hear a POST beep, see a Wyse BIOS screen flash and then boot CE from the flash. the DEL key to enter the BIOS.

    I would say they are toast, not really worth fixing them up…

    #16728
    thinkthin
    Member
    • Total Post: 1686
    • Jacked into The Matrix
    • ★★★★★★

    I am assuming of course you have the correct power supply hooked up (V. AMP and pin out)

    #16729
    yobortsa
    Member
    • Total Post: 5
    • Newbie
    • ★

    I have three of these WT3125SE units and they all act the same. Surely one of them would at least give a display and this POST beep you speak of.

    I know they came from Dept of Defense – is it possible they may have wiped the flash for security reasons? Is there a way I can re-flash them with the factory BIOS/operating system?

    Can you run a crossover serial cable at, say, 9600/8/N/1 for administration at a basic level?

    Thanks.

    #16730
    yobortsa
    Member
    • Total Post: 5
    • Newbie
    • ★

    I am running a 12V 2 amp supply to the DC connector (centre pin +ve). Perhaps I should try a different power supply. This one is from an external SATA hdd unit.

    #16731
    yobortsa
    Member
    • Total Post: 5
    • Newbie
    • ★

    I just tried running the unit off a fully charged 32Ah deep cycle 12V battery and exactly the same result. Perhaps they are all unserviceable. Just wish I had one unit that I knew worked so I could compare it with the others.

    #16733
    thinkthin
    Member
    • Total Post: 1686
    • Jacked into The Matrix
    • ★★★★★★

    See netXfer to re-flash:

    http://www.freewysemonkeys.com/modules.php?name=News&file=article&sid=55

    The power is correct – the PSU with the unit is 12v 2A center pin +

Viewing 9 posts - 1 through 9 (of 9 total)
  • You must be logged in to reply to this topic.