Prevent Autolaunch for Citrix Desktops

Viewing 7 posts - 1 through 7 (of 7 total)
  • Author
    Posts
  • July 10, 2019 at 7:22 pm #50279
    mtnbikeninja
    Participant
    • Total Post: 30
    • Frequent Flyer
    • ★★★

    I’m new to managing WYSE 5010 devices running ThinOS 8.5.  What users are running into is they login to the VDI broker and receive both VMware Horizon and Citrix Desktops, both are autolaunching.  I would like to know what I need to set the wnos.ini to prevent the Citrix and VMware desktops from autolaunching.  If this isn’t possible, I just need the Citrix desktops to stop autolaunching.

    July 11, 2019 at 10:42 am #50294
    ConfGen
    Keymaster
    • Total Post: 10696
    • Jedi Master
    • ★★★★★★★

    Use
    SessionConfig=ALL AutoConnect=no

    CG

    July 11, 2019 at 2:58 pm #50297
    mtnbikeninja
    Participant
    • Total Post: 30
    • Frequent Flyer
    • ★★★

    Thanks!  I tested this and I believe it resolved our issue.  So glad I found this site!

    July 11, 2019 at 9:40 pm #50302
    mtnbikeninja
    Participant
    • Total Post: 30
    • Frequent Flyer
    • ★★★

    So, my users are very needy.  They want their VMware Horizon VMs to autolaunch but not their Citrix VDI.  Below are the parameters in the wnos.ini file.  What should I add or change to allow this behavior?

    SysMode=VDI ToolBarDisableMouse=no ToolbarEnableOneSession=yes

    Inactive=480
    AutoSignoff=yes Reboot=yes
    Shutdowncounter=0

    KeySequence=yes Ctrl+Alt+Up=yes Ctrl+Alt+Down=yes Ctrl+Alt+Left=no Ctrl+Alt+Right=no

    DesktopColorDepth=16 RGB565=yes
    DeskColor=”62 107 130″
    Desktop=Disclaimer.jpg Layout=center

    Timeserver=172.16.0.226 Timeformat=”12-hour format” Dateformat=mm/dd/yyyy
    TimeZone=’GMT – 05:00′ ManualOverride=yes Daylight=yes Start=030207 End=110107 TimeZoneName=”Eastern Standard Time” DayLightName=”Eastern Daylight Time”

    Device=Ethernet Speed=”Auto”
    SignOn=yes DisableGuest=yes EnableOK=Yes
    DomainList=cmgmi

    ;Service=VNCD disable=yes

    ConnectionBroker=VMWare SecurityMode=Warning ConnectionType=Blast
    VDIBroker=desktop.archmi.com

    SessionConfig=ALL AutoConnect=no

    July 15, 2019 at 11:50 am #50310
    ConfGen
    Keymaster
    • Total Post: 10696
    • Jedi Master
    • ★★★★★★★

    How do you configure the Citrix environment? I do not see anything in your config.

    CG

    July 15, 2019 at 5:06 pm #50316
    mtnbikeninja
    Participant
    • Total Post: 30
    • Frequent Flyer
    • ★★★

    Currently, all devices point to a wnos.ini that doesn’t have any configs for Citrix, only VMware Horizon.  However, most of the users still have access to both.  I found an old wnos.ini that they used to point to that had the Pnliteserver settings.  Should I put those parameters in the new wnos.ini and try that?

    July 16, 2019 at 12:06 pm #50324
    ConfGen
    Keymaster
    • Total Post: 10696
    • Jedi Master
    • ★★★★★★★

    You should always have all the parameters needed by the users listed in your wnos.ini.
    Do never rely on old settings stored on the clients. These will be gone after a factory reset.

    CG

  • Author
    Posts
Viewing 7 posts - 1 through 7 (of 7 total)
  • You must be logged in to reply to this topic.